Secure installation

For Geotab Trusted Installers, third-party installers with a Geotab account, and Customers who self-install.

The secure installation flow is available to Geotab Trusted Installers, third-party installers with a Geotab account, and Customers who self-install. Log in to MyGeotab or MyAdmin to access this flow.

To get an accurate status reading, run the engine and make sure the device's red and green LEDs are lit.

Select the type of work to begin:

Geotab Trusted Installers can also manage work orders. See Work orders.

New device installation

For installers verifying that a newly installed device is connected and working.

As an installer, you run this check during the install. The check confirms the device is connected to the network and captures asset details and photos.

  1. Access the installation flow in any of the following ways:
    • MyAdmin: Navigate to Install > Verify an Installation.
    • MyGeotab: Navigate to Installation > Verify an Installation.
    • Scan the QR code from the device packaging, then tap Install.
  2. If you are installing on behalf of a Customer, enter an install code or select a work order.
  3. Confirm that the Customer name on the screen matches the Customer you are installing for. If it does not, click No, this is incorrect.
  4. Tap New Installation.
  5. Enter the serial number of the installed device in any of the following ways:
    • Scan the device serial number (QR or bar code) using your mobile device.
    • Tap Enter serial number manually, enter the serial number, then tap Confirm.

    If you are also removing a non-Geotab device, tap Did you remove an old device? to enter the removed device serial number.

    Note: For the removal of a Geotab device, see Device removal.
  6. Review the device status.

    The app takes a moment to check the device status and displays the result as a Pass or Fail.

    DevicePassFail
    GO device or third-party deviceCommunicated with the network within the last 24 hours.Has not communicated with the network within the last 24 hours.
    GO AnywhereCommunicated with the network within the last 75 hours.Has not communicated with the network within the last 75 hours.
  7. Under Check device status, review the details to make sure all connected harnesses and IOX devices you installed are detected.
    • Set up any IOX devices or integrated auxiliaries with the blue Set up pill.
    • If there are no IOX devices or integrated auxiliaries to set up, continue to Asset details.
IOX device setup
  1. Tap Setup beside the IOX device or integrated auxiliaries to start.
  2. Follow the on-screen instructions to complete the setup.

    Once the IOX device has been successfully set up, you will return to the Check device status step.

Asset details
  1. Under Input asset information, select the relevant Asset type from the dropdown.
  2. Enter details about the vehicle or asset where the telematics device was installed, then tap Continue.
    Note: Fields displayed may vary based on the asset and device type.
Installation photos
  1. Upload photos of the installation.

    You can take a photo with your mobile device or attach an image from your photo library. The number of photos required depends on the device being installed.

    Important: Ensure that photos do not capture personally identifiable or confidential details.
  2. Tap Continue.
Review and finish
  1. Review details by tapping any section. If needed, update any captured details.
  2. Tap Finish.
The installation is verified and logged on the Installation Report page.

Device removal

For installers verifying that the correct device was removed from an asset and recording asset details and photos.

Before you begin: Before you start, you must have the following:

  • Device serial number (available on the device or its packaging).
  • VIN
  • Camera ID (if a camera was installed)
  1. Access the installation flow in any of the following ways:
    • MyAdmin: Navigate to Install > Verify an Installation.
    • MyGeotab: Navigate to Installation > Verify an Installation.
  2. Tap Remove.
  3. Enter the serial number of the device in any of the following ways:
    • Scan the device serial number (QR or bar code) using your mobile device.
    • Tap Enter serial number manually, enter the serial number, then tap Confirm.
  4. Review the device status.

    The app takes a moment to check the status.

  5. Under Check device details, review the information to make sure it belongs to the unit you are removing.

    Optional: Add comments about the device.

  6. Tap Continue.
  7. Under Input asset information, select the relevant Asset type from the dropdown.
  8. Enter details about the vehicle or asset that the telematics device was removed from, then tap Continue.
    Note: Fields displayed may vary based on the asset and device type.
  9. Upload photos of the installation.

    You can take a photo with your mobile device or attach an image from your photo library. The number of photos required depends on the device being installed.

    Important: Ensure that photos do not capture personally identifiable or confidential details.
  10. Tap Continue.
  11. Review details by tapping any section. If needed, update any captured details.
  12. Tap Finish.
The device removal is verified and logged on the Installation Report page.

Device swap

For installers verifying a device replacement on the same asset.

Before you begin: Before you start, you must have the following:

  • Device serial number — available on the device or its packaging.
  • VIN
  • Camera ID (if a camera was installed)

As an installer, you run this check when you replace one device with another on the same asset. Confirm both serial numbers, check that the new device is connected to the network, then provide asset details and add photos. The job is logged on the Installation Report page.

You can also set up any connected IOX devices as part of this process.

  1. Access the installation flow in any of the following ways:
    • MyAdmin: Navigate to Install > Verify an Installation.
    • MyGeotab: Navigate to Installation > Verify an Installation.
    • Scan the QR code from the device packaging, then tap Install.
  2. Tap Swap.
  3. Enter the serial number of the removed device in any of the following ways:
    • Scan the device serial number (QR or bar code) using your mobile device.
    • Tap Enter serial number manually, enter the serial number, then tap Confirm.
    Scan the serial number on the device being removed.
  4. Enter the serial number of the installed device in any of the following ways:
    • Scan the device serial number (QR or bar code) using your mobile device.
    • Tap Enter serial number manually, enter the serial number, then tap Confirm.
  5. Review the device status.

    The app takes a moment to check the device status and displays the result as a Pass or Fail.

    Device Pass Fail
    GO device or third-party device Communicated with the network within the last 24 hours. Has not communicated with the network within the last 24 hours.
    GO Anywhere Communicated with the network within the last 75 hours. Has not communicated with the network within the last 75 hours.
  6. Under Check device status, review the details to make sure all connected harnesses and IOX devices you installed are detected.
IOX device setup
  1. Tap Setup beside the IOX device or integrated auxiliaries to start.
  2. Follow the on-screen instructions to complete the setup.

    Once the IOX device has been successfully set up, you will return to the Check device status step.

Asset details
  1. Tap Continue.
  2. Under Input asset information, select the relevant Asset type from the dropdown.
  3. Enter details about the vehicle or asset where the telematics device was installed, then tap Continue.
    Note: Fields displayed may vary based on the asset and device type.
Installation photos
  1. Upload photos of the installation.

    You can take a photo with your mobile device or attach an image from your photo library. The number of photos required depends on the device being installed.

    Important: Ensure that photos do not capture personally identifiable or confidential details.
  2. Tap Continue.
Review and finish
  1. Review details by tapping any section. If needed, update any captured details.
  2. Tap Finish.
The device swap is verified and logged on the Installation Report page.

Device service

For installers recording the reason for a service visit and the work done on a device.

Before you begin: Before you start, you must have the following:

  • Device serial number — available on the device or its packaging.
  • VIN

As an installer, you run this check when you service a device that is already installed. You'll select a reason for the service, describe the work, then provide asset details and add photos. The job is logged on the Installation Report page.

  1. Access the installation flow in any of the following ways:
    • MyAdmin: Navigate to Install > Verify an Installation.
    • MyGeotab: Navigate to Installation > Verify an Installation.
    • Scan the QR code from the device packaging, then tap Install.
  2. Tap Service.
  3. Enter the serial number of the installed device in any of the following ways:
    • Scan the device serial number (QR or bar code) using your mobile device.
    • Tap Enter serial number manually, enter the serial number, then tap Confirm.
  4. Review the device status.

    The app takes a moment to check the device status and displays the result as a Pass or Fail.

    Device Pass Fail
    GO device or third-party device Communicated with the network within the last 24 hours. Has not communicated with the network within the last 24 hours.
    GO Anywhere Communicated with the network within the last 75 hours. Has not communicated with the network within the last 75 hours.
  5. Under Check device status, review the details to make sure all connected harnesses and IOX devices you installed are detected.
  6. Tap Continue.
  7. Select the relevant Service type from the dropdown.
  8. Provide details about the service performed in the Service details field, then tap Continue.
    Service type and service details fields in MyInstall.
  9. Under Input asset information, select the relevant Asset type from the dropdown.
  10. Enter details about the vehicle or asset where the telematics device was installed, then tap Continue.
    Note: Fields displayed may vary based on the asset and device type.
  11. Upload photos of the installation.

    You can take a photo with your mobile device or attach an image from your photo library. The number of photos required depends on the device being installed.

    Important: Ensure that photos do not capture personally identifiable or confidential details.
  12. Tap Continue.
  13. Review details by tapping any section. If needed, update any captured details.
  14. Tap Finish.
The device service is verified and logged on the Installation Report page.

Work orders

For Geotab Authorized Installers who manage and process assigned work orders.

Note: Work orders are applicable to Geotab Trusted Installers only.

Work orders are created by Geotab and are assigned only to Geotab Trusted Installers. When an installer accesses the Verify an Installation page, they are automatically sent to the Work Orders page.

Each work order includes:

  • Company details: The name and address of the company needing service.
  • Work order number: A unique ID for the specific work order.
  • Contact information: The name and phone number of the company contact who asked for the service.
  • Service requested: Shows the type of service needed (such as installation, removal, add-on, and more).

To start an installation or service, select the work order. You will be taken through the selected process.

Searching for a work order

Work orders are applicable to Geotab Trusted Installers only. This shows you how to search for and find your assigned work order.

Prerequisites:

  • You must have a Trusted installer account to complete this task.
  • You must have a work order assigned to you.
  1. Navigate to Install > Verify an Installation in the main menu.

    The Work Orders page is displayed if there are available work orders.

  2. In the Search bar, enter a work order number, company name, or address.

    Work order selection page with a search bar and available work orders.

  3. Optional: Click Filters to access more filters.
    1. Select one or more service types to show specific types.
    2. Click Apply.

MyAdmin displays a list of work orders that match your filter criteria.

After selecting the work order, continue with the requested verification: