GO8 RUGGED installation

Prepare to install and test a GO8 RUGGED device.

GO8 RUGGED installation warnings

Review key warnings for installing GO8 RUGGED.

Important:

Professional Installation Required

Installation of the GO device requires that the installer have sufficient technical knowledge and expertise for mobile device installation and integration into modern vehicles, such as a Certified Geotab Installer certification or equivalent.

Warning:

Read and follow all safety information, including limitations of use, before installation. Failure to follow these instructions and warnings can result in loss of vehicle control, serious injury, or vehicle damage.

Warning:

Do not install, reconfigure, or remove this product while the vehicle is in motion or otherwise in operation. Complete all installation, configuration, and removal work only when the vehicle is stationary and securely parked.

Attempting to service devices while the vehicle is in motion could result in malfunctions or collisions, leading to death or serious personal injury.

Warning:

Secure all in-vehicle devices and related cabling, and keep them clear of vehicle controls, including the gas, brake, and clutch pedals. Use a cable tie to secure the device or extension harness to the OBD connector. Secure both sides of the harness. Without a cable tie, vehicle vibration can loosen the connection and indirectly cause engine computer failure, loss of vehicle control, or serious injury. Inspect devices and cabling regularly to confirm that they remain securely attached.

Warning:

If a vehicle warning light illuminates after installation, or the vehicle stalls or has a marked decrease in performance, shut off the engine, remove the device, and contact an authorized Partner.

Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.

Installing a GO8 RUGGED device

Learn how to connect, mount, and verify a GO8 RUGGED device.

  1. Locate the vehicle engine diagnostic port. Align the OBD connector on the HRN-RS12S2 (sold separately) with the diagnostic port and push it in place.

    The port is typically in the driver area at or below knee level. Heavy-duty vehicles use a different connector system. Contact an authorized Partner for heavy-duty connector applications, or for extension harnesses if the device must be placed away from the diagnostic port.


    Vehicle diagnostic port and connected harness.
  2. Connect the 12-pin male connector on the device to the 12-pin female connector on the HRN-RS12S2 harness and click it into place.

    Ensure that all connections are secure. All three lights on the device flash briefly.


    GO8 RUGGED connected to the harness.
  3. Connect an IOX, if applicable.

    Connect the 6-pin female connector on the device to the 6-pin male connector on the HRN-RX06S4 and click it into place. Connect the female mini-USB connector on the other side of the HRN-RX06S4 to the male mini-USB connector on the IOX. Secure the two USB connectors with a cable tie.


    GO8 RUGGED connection to an IOX harness.
  4. Start the vehicle outdoors and allow it to run for approximately three minutes.

    Starting the vehicle outdoors helps the device locate satellites and allows exhaust fumes to vent. The red LED powers on, then the green and blue LEDs light up when the device connects to the cellular and GPS networks. Initial startup can take several minutes.

  5. When all three LEDs are lit, mount the device in a location where the wiring does not interfere with safe vehicle operation.

    Drill 5/32 inch pilot holes, then secure the device with the supplied hex washer-head screws.


    GO8 RUGGED fastened in the installation location.
  6. Point the GPS antenna toward the sky.

    The GPS antenna is on the same face as the device label. Keep the antenna pointing up toward the sky at all times for faster GPS latch times.

  7. Keep the IOX connector sealing cap in place when an IOX is not installed.

    Remove the cap only when installing an IOX with an HRN-RX06S4 adapter cable. Align the cap arrow with the lock clip at the top of the six-pin connector. Other cap orientations do not guarantee a waterproof and dustproof seal.


    GO8 RUGGED weatherproof cap aligned with the connector lock clip.
  8. Go to installmygps.com to verify that the device is communicating.

    Enter the installer name, company name, and GO device serial number, which is found at the bottom of the device. Click Log Install.

    The page displays the current communication status of the device. If the device is communicating, the status is displayed in green text with the last valid GPS record. If the device is not communicating, the status is displayed in red text and the installation must be verified.


    The installmygps.com form includes installer name, company, and device serial number fields.