For Cold Chain Solution (ThermoKing Direct Smart Reefer (DSR) Units)

Introduction

This document is the installation guide for integrating the telematics solution with Thermo King DSR units. This document provides technical information, installation instructions, the procedure to install the GO device, and important safety information.

Specifications and installation

Professional Installation Required — Installation requires the installer to have sufficient technical knowledge and expertise for mobile device installation and integration into modern vehicles, such as Certified Geotab^® Installer certification or equivalent.

This vehicle specific installation guide is based on Geotab’s suggested best practice, valid at time of publishing. There may be differences or revisions between specific vehicle models, trim-levels, equipment or accessories made by the vehicle manufacturer and these are beyond Geotab’s control. To ensure you have the latest available version of this document, or if you require any assistance, contact your Authorized Reseller before proceeding with the installation.

Preparing for installation

Before installing this solution, ensure that you have the following tools and components:

Tools

1. Screwdriver kit
2. Cable guide
3. Cable ties
4. Cutting pliers

Components

Installing the system

! IMPORTANT: Before opening the unit and installing the Cold Chain Solution, ensure that you switch off the in-cab controller.

! IMPORTANT: Professional installation (Certified Geotab® Installer or equivalent) is required for the safe and proper installation of this product (harness and/or IOX). The installer must have sufficient technical knowledge and expertise for the respective installation.

WARNING! Do not plug anything in the hole found on the side of the HRN-HTKDSR’s casing. This harness must not be added to the GO9 and IOX devices daisy chain.

WARNING! All IOX-COLD, IOX-UREADER, and GO Device cabling cabling must be securely fastened and routed clear of hot surfaces, vehicle controls, and moving components in the engine or refrigeration unit. Failure to do so may result in damaged components, refrigeration unit malfunction, or collisions leading to death or serious personal injury.

IMPORTANT! All powered connections must be fitted with overcurrent limit protection. Geotab offers the HRN-5AFUSKIT, this can help minimize configuration complexity, reduce installation time, and improve reliability.

Installation instructions (IOX-UREADER or IOX-COLD)

For light commercial vehicles, vans, or similar vehicles, follow the steps below to install the solution:

Important safety information and Limitations of Use

For the latest version of the Limitations of Use, visit: goo.gl/k6Fp0w.

WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could cause malfunctions or accidents, leading to death or serious personal injury.

WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.

WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your Reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.

WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may cause units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.

WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.

NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized Reseller or Installer. Unauthorized servicing of these products will void your product warranty.

Regulatory statements

USA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

✱ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Geotab could void the user’s authority to operate the equipment.

Canada

CAN ICES-003 (B) / NMB-003 (B)

EU

SCIP 0e3baafa-12be-43f2-9831-3207a907a5b6

Germany

Wir besitzen keine Versand- und Lagerfläche in Deutschland und sind nicht von der Rücknahmepflicht nach § 17 ElektroG betroffen.