0 mins to read•
0 mins to read•
Learn more about IOX-SATIRDv2, which allows GO devices to communicate over the IRIDIUM Network if the vehicle travels outside of cellular or network connection. With the IRIDIUM Satellite Modem, users can continue to track their fleet even when cellular connectivity is lost. This solution includes an emergency button add-on, which sends an “emergency” message through the satellite network to MyGeotab when triggered.
If a vehicle is in an area with no cellular or network connection, the Iridium® Satellite Modem allows the Geotab® GO™ device to communicate over the Iridium Network. With the Iridium Satellite Modem, users can continue to track their fleet even when cellular connectivity is lost.
! IMPORTANT: Partner preplanning: If installation takes place in an area of no or poor cellular coverage, the Partner must power up the Geotab GO device and all IOX accessories (IOX-SATIRDv2) in an area of good cellular connectivity and sequence ignition to ensure the firmware is up-to-date on all devices.
The IOX-SATIRDv2 allows the driver to send a top priority Emergency message through the satellite network to MyGeotab® by pressing an alert button (not included). For more information, refer to step 8 of the installation instructions.
Overall Length: 1810 mm
Widest Point: 31 mm W × 16 mm H
PC+ABS clamshell casing
CAN: 500 kbps (for daisy chaining)
RS-232 serial interface
Emergency Switch Wire: Open — shorted to ground
Nominal Input Voltage
12 V / 24 V
Iridium Interface: 900 mA @ 12 V/24 V
Current Draw IOX-SATIRDv2
on GOx daisy chain
40 mA at 12 V / 24 V Operating mode (typical/nominal current draw)
100 mA at 12 V / 24 V Operating mode (max. current draw)
0.4 mA at 12 V / 24 V Sleep mode (min. current draw)
−40 ℃ to +85 ℃
Iridium Satellite Antenna Connector: SMA male plug
Iridium Satellite Modem Connector: SMA female jack
Male Mini-USB Type-B Connector: Daisy chain power and CAN in
Female Mini-USB Type-B Connector: Daisy chain power and CAN out
Molex 12-pin Connector 43025-1200: Iridium modem
1: Brown - GND
2: White - DTR
4: Green - RX
6: Red - PWR
8: Yellow - TX
Molex Female Terminal 43030-0001
All GO7® and newer devices and variants
GO9 can source a maximum total current to the IOX in Daisy Chain
2500 mA at 12 V/24 V
✱ NOTE: For each IOX in the Daisy Chain, add the Max Current draw, and do not exceed the Max. Total IOX Current draw.
✱ NOTE: Professional Installation Required: Installation of the IOX-SATIRDv2 requires the installer to have sufficient technical knowledge and expertise for mobile device installation and integration into modern vehicles. i.e. Certified Geotab® Installer certification or equivalent.
WARNING! Prior to IOX-SATIRDv2 installation, read and follow the GO device installation instructions (goo.gl/rkLRiA) to verify any existing GO device installation is correct in preparation for IOX-SATIRDv2 installation. Incorrect installation of either the GO device, and/or IOX-SATIRDv2 can result in loss of vehicle control and serious injury.
WARNING! Prior to IOX-SATIRDv2 installation, read and follow Important Safety Information and Limitations of Use, located at the end of the document. Always read and follow all safety information to prevent loss of vehicle control and serious injury.
✱ NOTE: Terminating or suspending the GO device does NOT automatically deactivate the connected Iridium modem. Please submit a support ticket to request the deactivation of the Iridium modem.
Unplug the Geotab GO device from the vehicle and remove the IOX expansion port cover on the GO device.
Plug the 90° USB connector from the IOX into the GO device. Secure the USB connector using a cable tie. Please note that over tightening the cable tie may damage the USB connector.
✱ NOTE: Insert the USB connector in the orientation displayed in the image.
Choose an appropriate mounting location for the satellite modem.
✱ NOTE: The location you choose for the GO device influences the locations available to mount the Iridium Modem due to the wire length on the IOX-SATIRDv2. Please ensure the installation does not interfere with safe vehicle operation.
The Iridium satellite antenna has a magnet mount, as well as a ring of two-sided tape on the bottom of the antenna, to facilitate mounting the device on plastic. The antenna location must not interfere with the safe operation of the vehicle or obstruct the driver’s field of vision.
WARNING! Above Decks Equipment (ADE) transmits radio frequency (RF) energy that may cause thermal injuries including tissue damage from increased heating and body temperature. When the system power is ON, keep all personnel a minimum of 1.0 m (3.3 ft.) from the antenna. Failure to do so could result in serious injury or death.
If you choose to mount the antenna below the dashboard, please ensure there are no metallic objects or other obstructions directly above it that may interfere with satellite reception. It is highly recommended to mount the antenna out of sight and secured with at least one cable tie.
The antenna and IOX-SATIRDv2 cable are connected to the satellite modem at the same end as the status LEDs. The LEDs indicate Power (RED) and Connection Status (GREEN).
Once you connect the IOX-SATIRDv2 to the GO device, plug in the GO device and immediately start the vehicle. The GO device will enter debug mode.
IOX-SATIRDv2 has a two-wire pigtail composed of a blue wire and a black wire, which are the external trigger wires for the Iridium Alert (Panic) feature. These wires can be connected to an Alert Button (momentary contact switch). When this feature is triggered, the device starts a beeping sequence. The beeping stops once the message is received by MyGeotab. In MyGeotab, create an Engine Rule for Alert button depressed.
Navigate to myinstallpub.geotab.com to verify that the device is communicating.
✱ NOTE: If the device is not communicating, please ensure the device is installed correctly and try again.
The IOX comes with a termination shunt installed in the expansion port. If you plan to install more than one IOX in a daisy chain, you must remove the shunt from each device in the daisy chain, except for the last IOX connected. The shunt must remain in the last IOX and secured with a cable tie.
The shunt in the last IOX device ensures the GO device detects and configures the IOX as effectively as possible.
✱ NOTE: Failing to install the shunt in the last IOX could affect IOX communication. It is recommended that you secure the shunt using a cable tie if not already done.
158 g (0.35 lbs)
Overall Length: 80 mm (L)
Widest Point: 54 mm (W) × 23 mm (H)
Operating Temp.: −40 ℃ to +85 ℃
Nominal Input Voltage
12 V / 24 V
Operating Current: 100 mA to 125 mA
Standard with magnetic roof mount and sticky adhesive for optional dash mount. For best transceiver performance, mounting the Satellite antenna under the dash panels is not recommended.
Default Logging Features - Alert Button Notification: Allows the driver to send an emergency/distress log to head office. The Geotab device notifies the driver when the message is received by MyGeotab.
From the dropdown menu, select Request current location.
! IMPORTANT: To receive Iridium data, apply the Base Plan custom parameters in the table below to a GO device under cellular coverage.
! IMPORTANT: If the vehicle is out of cellular range, the GO device will not receive firmware updates or other device parameter updates.
Base Plan Logging Features
Location Update Frequency
Alert (Panic) Trigger on IOX-AUXM Wire #1
(Contact Geotab Support to change AUX #)
Note: An IOX-AUXM must be installed and daisy-chained with the IOX-SATIRDv2 to the GO device Male Mini-USB connector..
! IMPORTANT: Enabling these extended logging features may increase Iridium data usage. Please create a support ticket for the required custom parameters and for more information on these features.
For the latest version of the Limitations of Use, please visit: goo.gl/k6Fp0w.
WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.
WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake, and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.
WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your Reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.
WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.
WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.
NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instruction and transmitter operating conditions for satisfying RF exposure compliance.
L'antenne ou les antennes utilisées pour cet émetteur doivent être installées pour fournir une distance de séparation d'au moins 20 cm de toutes les personnes et ne doivent pas être co-localisées ou fonctionner en conjonction avec une autre antenne ou émetteur. Les utilisateurs et les installateurs doivent recevoir des instructions d'installation de l'antenne et les conditions de fonctionnement de l'émetteur pour satisfaire la conformité à l'exposition aux RF.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
✱ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications not expressly approved by Geotab could void the user’s authority to operate the equipment.