0 mins to read•
0 mins to read•
Learn more about IOX-ANALOG, which enables the GO device to read analog signals from a vehicle and its connected accessories. With MyGeotab, the IOX-ANALOG provides near real-time status information for analog sources and delivers notifications if readouts fall outside of user-defined values. It can monitor up to four analog inputs.
The IOX-ANALOG enables the GO™ device to read analog signals from a vehicle and its connected accessories.
With MyGeotab™, the IOX-ANALOG provides near real-time status information for analog sources and delivers notifications, if readouts fall outside of user-defined values.
Overall length: 1140 mm L
Widest point: 31 mm W × 16 mm H
PC+ABS clamshell casing
CAN: 500 kbps (for daisy-chaining)
AUX1, AUX2, AUX3, AUX4
Nominal Input Voltage
12 V / 24 V
Input Impedance of each AUX: 30.3 kΩ
Driving circuit resistance must be less than 100 Ω
Current Draw IOX-ANALOG
on GOx daisy chain
40 mA at 12 V / 24 V Operating mode (typical/nominal current draw)
100 mA at 12 V / 24 V Operating mode (max. current draw)
0.4 mA at 12 V / 24 V Sleep mode (min. current draw)
-40 ℃ to +85 ℃
Molex 8-pin Connector 43020-0800
4. White - AUX 4
5. Green - AUX 3
6. Orange - AUX 2
7. Blue - AUX 1
Molex Male Terminal 43031-0001
Male Mini-USB Type-B connector: Daisy chain power and CAN in
Female Mini-USB Type-B connector: Daisy chain power and CAN out
Male Mini-USB connector connects to the GO device or another IOX™ harness
Input must connect to the intended circuit
All GO7® and newer devices and variants
GO9® can source a maximum total current to the IOX in Daisy Chain
2500 mA at 12 V/24 V
✱ NOTE: For each IOX in the Daisy Chain, add the Max Current draw, and do not exceed the Max.Total IOX Current draw.
✱ NOTE: Professional Installation Required — Installation of the IOX-ANALOG requires the installer to have sufficient technical knowledge and expertise for mobile device installation and integration into modern vehicles, such as a Certified Geotab® Installer certification or equivalent.
WARNING! Prior to IOX-ANALOG installation, read and follow GO device installation instructions to verify any existing GO device installation is correct in preparation for IOX-ANALOG installation. Incorrect installation of either the GO device, and/or IOX-ANALOG can result in loss of vehicle control and serious injury.
WARNING! Prior to IOX-ANALOG installation, read and follow Important Safety Information and Limitations of Use, located at the end of the document. Always read and follow all safety information to prevent loss of vehicle control and serious injury.
Identify and test the connection points for the auxiliaries you wish to monitor. Keep in mind that the IOX wire has a reach of approximately 3.5 feet (1.07 meters) from the GO device mounting location. Extending the wire to reach some connection points may be necessary. Make the auxiliary connections and secure them using an approved method, such as a T-tap wiring. Ensure none of the components or wiring interferes with the safe vehicle operation.
Unplug the Geotab GO device from the vehicle and remove the IOX expansion port cover on your GO device.
Plug the 90° USB connector from the IOX in to the GO device. Secure the USB connector using a zip tie. Please note that over tightening the zip tie may damage the USB connector.
✱ NOTE: Insert the USB connector in the orientation displayed in the image.
The IOX-ANALOG has four inputs — configured and labeled Aux 1–4. Connect the desired auxiliaries in the vehicle to the IOX-ANALOG wires, as needed. The IOX-ANALOG records voltage readings from 0–30 V and adjusts the reporting error based on the range of values it sees. As a result, the IOX-ANALOG reports small changes for a lower range, and larger changes for a higher range.
Once you connect the IOX-ANALOG to the GO device, plug in the GO device and immediately start the vehicle. The GO device enters debug mode.
Navigate to myinstallpub.geotab.com to verify that the device is communicating.
✱ NOTE: If the device is not communicating, please ensure the device is installed correctly and try again.
The IOX comes with a termination shunt installed in the expansion port. If you plan to install more than one IOX in a daisy chain, you must remove the shunt from each device in the line, except for the last IOX connected. The shunt must remain in the last IOX and secured with a zip tie.
The shunt in the last IOX ensures the GO device detects and configures the IOX, as effectively as possible.
✱ NOTE: Failure to install the shunt in the last IOX may affect IOX communication. To ensure the IOX communicates, please secure the shunt with a zip tie.
For the latest version of Limitations of Use, please visit: goo.gl/k6Fp0w.
WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.
WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.
WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.
WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.
WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.
NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
✱ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications not expressly approved by Geotab could void the user’s authority to operate the equipment.
CAN ICES-003 (B) / NMB-003 (B)
Wir besitzen keine Versand- und Lagerfläche in Deutschland und sind nicht von der Rücknahmepflicht nach § 17 ElektroG betroffen.