GO8 RUGGED installation prerequisites

Prerequisites and preparation steps before installing the GO8 RUGGED.

Before installing the device, document its serial number. You will need this information later to verify that the installation was completed successfully.

Verify that we support your vehicle by carefully reading the Vehicle-Specific Installation Notes. If you have any questions or concerns, please consult your Authorized Reseller.

Ensure no dash warning lights are on in the vehicle while it is running, and all other functions such as headlamps, flashers, etc., are working before installing the device.

Before installing, add the device to your MyGeotab database using the device serial number. This ensures that all data logged by the device is sent to the database.

GO8 RUGGED installation instructions

Step-by-step installation instructions for the GO8 RUGGED.

Professional Installation Required — Installation of the GO8 RUGGED requires that the installer has sufficient technical knowledge and expertise for mobile device installation and integration into modern vehicles, i.e. Certified Geotab Installer certification or equivalent.

Read important related safety information and limitations of use following these installation instructions. Read and follow all instructions and warnings to prevent serious injury and/or vehicle damage.

Warning:

Prior to GO installation, read and follow important safety information including limitations of use located following these installation instructions. Always read and follow all safety information to prevent loss of vehicle control and serious injury.

Warning:

Do not attempt to install, re-configure or remove any product from a vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service devices while the vehicle is in motion could result in malfunctions or accidents, leading to death or serious personal injury.

  1. Locate the vehicle’s engine diagnostic port, typically found in the driver’s area at or below knee level. Align the OBD connector on the HRN-RS12S2 (sold separately) with the vehicle diagnostic port and push in place. Note: Heavy-duty vehicles use a different connector system. Contact your Authorized Geotab Reseller for heavy-duty connector applications or for extension harnesses should it be necessary to place your device away from the engine diagnostic port.
  2. Connect the 12-pin male connector on the device to the 12-pin female connector on the HRN-RS12S2 as shown, and click into place. Ensure that all connections are secure. All three lights on the device will flash briefly.
  3. If you are also installing an IOX, connect the 6-pin female connector on the device to the 6-pin male connector on the HRN-RX06S4 and click into place. Connect the female mini-USB connector on the other side of the HRN-RX06S4 to the male mini-USB connector on your IOX. Ensure that the two USB connectors are secured with a zip tie.
  4. With the vehicle parked outdoors to locate satellites and vent exhaust fumes, start the vehicle and allow it to run for approximately 3 minutes. During this time period, you will notice that the Red LED will power on and light up on the face of the device. Shortly afterwards, the Green and Blue LEDs will light up when the device connects to the cellular and GPS networks. This initial startup may take several minutes to complete.
  5. Once all three LEDs have lit up, select a location to attach your device. Drill 5/32 inch pilot holes first then secure the device into place using the supplied Hex Washer head screws. Ensure that you install your device in a location where the wires will not interfere with the safe operation of the vehicle.
  6. The GPS antenna in the GO8 RUGGED is located on the same face as the label. Make sure that the antenna is always pointing upwards towards the sky for faster GPS latch times.
  7. The 6-pin weatherproof female connector of the telematics device comes covered with a sealing cap for waterproofing and dustproofing. Remove the cap only if you plan on using an IOX (requires HRN-RX06S4 adapter cable). Otherwise, keep the cap in place with the arrow facing towards the lock clip located at the top of the 6-pin female connector as shown. Attaching the sealing cap in any other orientation will not guarantee a waterproof and dustproof seal.
  8. Navigate to the MyInstall tool to finalize the installation. The MyInstall tool requires MyAdmin access and is mandatory for every installation to correctly configure the device.
Warning:

All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. This requires the use of a cable tie when securing the device or any extension harness to the OBD connector, securing both sides of the harness. If you do not use a cable tie, vibration in the vehicle can lead to a loose connection that could indirectly cause the vehicle's engine computer to fail, loss of vehicle control, and cause serious injury. Inspect devices and cabling regularly to ensure that all devices and cabling continue to be securely attached.

Warning:

If at any point after an in-vehicle device is installed a warning lights up on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control and serious injury.