3-Wire Harness Kit Compatible with GO10 and GO10 Plus - HRN-XCW03K3
Support Document
0 mins to read
The HRN-XCW03K3 kit includes the HRN-XCW03S3 harness and a fuse kit. The HRN-XCW03K3 kit connects to a Geotab® GO10 or GO10 Plus device to vehicles where a diagnostic port is not available - due to the age or type of vehicle (i.e. golf carts, generators, older vehicles, ect.); or to track the vehicle without connecting to the vehicle bus (i.e. asset tracking).
3-Wire Harness Kit Compatible with GO10 and GO10 Plus - HRN-XCW03K3
For the most up-to-date version, please visit: https://gtb.link/1xG10
! IMPORTANT: USA Only: The GO10 and GO10 Plus Devices have not been granted CARB Executive Order (EO) exemption. Installation of these devices on vehicles registered or primarily operated in the State of California is prohibited and may violate California emissions regulations. Do not install in California until a CARB EO number has been issued and communicated by Geotab.
The HRN-XCW03K3 kit includes the HRN-XCW03S3 harness and a fuse kit. The HRN-XCW03K3 kit connects to a Geotab® GO10 or GO10 Plus device to vehicles where a diagnostic port is not available - due to the age or type of vehicle (i.e. golf carts, generators, older vehicles, ect.); or to track the vehicle without connecting to the vehicle bus (i.e. asset tracking).
Harness Technical Specifications
Weight | 193.4 g |
Size | Max Length: 630 mm Max Width: 40.7 mm |
Material | Universal Core Connector: PBT + 15% Glass filled Wire Jacket: Black PVC Jacket |
Connectors | 1 × 12V compatible Red Connector 1 × Universal Core Connector 1 × Geotab® GO10 and GO10 Plus compatible Custom Connector |
Power Output | 12 V to 24 V |
Current Rating | 5 A |
Temperature Rating | −40 to +85 °C |
Harness Wires | See the Harness Wires section below |
WARNING! The HRN-XCW03K3 harness kit is designed and intended for use only with the GO10 and GO10 Plus devices or Geotab-authorized accessory devices. Professional installation from a Geotab Authorized Installer is required. Read and follow the complete GO10 or GO10 Plus device installation instructions, as well as the installation instructions in this document to prevent serious personal injury or significant damage to your vehicle.
Harness Wires
The HRN-XCW03S3 harness has three wires that connect to power, ground and ignition. With a wide variety of applications, the fuse kit may help minimize complexity, reduce installation time and improve safety.
- RED - POWER
- The constant power (12V or 24V) wire must be connected to a true battery source (live at all times).
- BLACK - GROUND
- The ground wire must be connected to a known verified ground.
- YELLOW - IGNITION
- The ignition sense wire must be connected to a true ignition source (12V or 24V when the key is in both ON and RUN positions, and zero when in OFF position).
Harness Assembly Instructions
Please visit https://installguides.geotab.com/ for more information.
Important Safety Information and Limitations of Use
For the latest version of the Limitations of Use, refer to: https://gtb.link/k6Fp0w
WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.
WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.
WARNING! If at any point after an in-vehicle device is installed a warning lights up on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.
WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.
WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.
NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.
Regulatory Statements
Germany
Wir besitzen keine Versand- und Lagerfläche in Deutschland und sind nicht von der Rücknahmepflicht nach § 17 ElektroG betroffen.
