0 mins to read•
0 mins to read•
Learn more about IOX-NFCREADERA, which integrates Near Field Communication (NFC) with the Geotab GO device to identify the drivers operating vehicles in a fleet at any given time. Users can create rules, reports, and exceptions on MyGeotab based on individual drivers or vehicles and can track driver data across different vehicles to enable driver based reporting.
The IOX-NFCREADERA integrates Near Field Communication (NFC) with the Geotab® GO™ device to identify drivers operating vehicles in a fleet at any given time. Users create rules, reports, and exceptions on MyGeotab™ based on individual drivers or vehicles
Overall Length: 1300 mm L
Widest Point (Antenna): 63 mm L x 49 mm W x 16.5 mm H
Widest Point (Connector): 53 mm W × 15 mm H
Black, moisture-resistant thermoplastic overmold
CAN: 500 kbps (for daisy-chaining)
Ground Switch: For Relay Control
Nominal Input Voltage
12 V / 24 V
Daisy Chaining: 2500 mA @ 12 V/24 V
Operating Mode: 100 mA
Sleep Mode: 1.1 mA
−40 ℃ to +85 ℃
Male Mini-USB Type-B connector: Daisy chain power and CAN in
Female Mini-USB Type-B connector: Daisy chain power and CAN out
2-pin grounding socket (Molex connector)
Male Mini-USB connector connects to the GO device or another IOX
Relay module connects to 2-pin socket
With GEO-NFCSTKBLU: 19 mm
With GEO-NFCFOBBLU: 11 mm
All GO7® and newer devices and variants
WARNING! Prior to IOX-NFCREADERA installation, read and follow GO device installation instructions (https://goo.gl/rkLRiA) to both verify any existing GO device installation is correct and that you are qualified to complete this IOX-NFCREADERA installation. Incorrect installation of either the GO device or IOX-NFCREADERA can result in loss of vehicle control and serious injury.
WARNING! Prior to IOX-NFCREADERA installation, read and follow Important Safety Information and Limitations of Use, located at the end of the document. Always read and follow all safety information to prevent loss of vehicle control and serious injury.
NFC tags typically operate at relatively low input powers/low voltage, and this NFC product is not designed to be able to operate when exposed to a wireless charging electromagnetic field. Affix the NFC Tag/Sticker on a wallet or employee identification card, or other ID you have with your person.
WARNING! Do NOT place the NFC sticker/tag near wireless charging (e.g., the back of a cell phone) to prevent thermal damage or serious injury.
Unplug the Geotab GO device from the vehicle and remove the IOX expansion port cover on the GO device.
Plug the 90° USB connector from the IOX into the GO device. Secure the USB connector using a zip tie. Please note that over tightening the zip tie may damage the USB connector.
✱ NOTE: Insert the USB connector in the orientation displayed in the image.
Choose an appropriate location to mount the NFC Reader within safe reach of the driver.
✱ NOTE: The location you choose for the GO device influences the locations available to mount the accessory due to the wire length on the IOX-NFCREADERA. Please ensure the installation does not interfere with safe vehicle operation.
The NFC Reader comes with a convenient mounting bracket that can either be screwed in place (screws provided) or taped in place (tape provided). The reader snaps into the bracket.
When using tape, ensure the mounting surface is thoroughly clean and dry, and at least 65 °F (18 °C). Hold the tape firmly in place for 60 seconds to ensure the tape has bonded to the surface.
✱ NOTE: We recommended mounting IOX-NFCREADERA on the front windshield using SPR-ADHNFCM adhesive tape.
Once you connect the IOX-NFCREADERA to the GO device, plug in the GO device and immediately start the vehicle. The GO device enters debug mode.
To test the NFC Reader installation, touch a valid NFC Tag to the reader. The green LED on the reader flashes twice and the GO device emits a single beep when the tag is read. Repeat this step for each additional tag.
If a Driver ID Relay is installed and the feature is active in MyGeotab, you must swipe a valid ID tag to activate the relay. Failure to activate the relay, prior to use, causes the GO device to beep continuously and the electrical connection, driven by the relay, remains inactive until a valid key tag is swiped on the reader.
Navigate to myinstallpub.geotab.com to verify that the device is communicating.
✱ NOTE: If the device is not communicating, please ensure the device is installed correctly and try again.
When connecting additional IOXs to an IOX-NFCREADERA, ensure the USB connector is seated correctly and secure the connection with a zip tie.
The IOX comes with a termination shunt installed in the expansion port. If you plan to install more than one IOX in a daisy chain, you must remove the shunt from each device in the line, with the exception of the last IOX connected. The shunt must remain in the last IOX and secured with a zip tie.
The shunt in the last IOX device ensures the GO device detects and configures the IOX, as effectively as possible.
✱ NOTE: Failing to install the shunt in the last IOX could affect IOX communication. It is recommended that you secure the shunt using a zip tie if not already done.
To create an authlist of authorized drivers for a particular GO device, apply the following custom parameter to the GO device through MyGeotab:
<Parameter Description="Enable Authorized Driver List" Offset="164" Bytes="8" IsEnabled="true"/>
Once the parameter is applied, the IOX-NFCREADERA only accepts driver key tags assigned to an authorized driver. You can add and remove drivers to/from the authlist through the Geotab API (my.geotab.com/sdk/#/api). See the DriverAuthListContent object for more details.
The authlist mode is disabled when the custom parameter is removed from the GO device.
The previous version of the IOX-NFCREADER is shown below.
To enable the relay option in MyGeotab, prior to IOX installation:
Navigate to MyGeotab.
Select Vehicles & Assets, located in the navigation menu to the left.
Select the GO device.
Select the Audio feedback tab.
For Driver identification reminder, click On and set the time limit using the slider.
✱ NOTE: Requires Professional Installation — To install a Driver ID Relay in conjunction with the IOX-NFCREADERA, please review the instructions in the SPR-RELAYKIT Install document (goo.gl/Dljbok).
The IOX-NFCREADERA cannot be used in conjunction with the IOX-HID.
For the latest version of the Limitations of Use, please visit: goo.gl/k6Fp0w.
WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.
WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.
WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your Reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.
WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.
WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.
NOTICE — This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instruction and transmitter operating conditions for satisfying RF exposure compliance.
L'antenne ou les antennes utilisées pour cet émetteur doivent être installées pour fournir une distance de séparation d'au moins 20 cm de toutes les personnes et ne doivent pas être co-localisées ou fonctionner en conjonction avec une autre antenne ou émetteur. Les utilisateurs et les installateurs doivent recevoir des instructions d'installation de l'antenne et les conditions de fonctionnement de l'émetteur pour satisfaire la conformité à l'exposition aux RF.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
✱ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications not expressly approved by Geotab could void the user’s authority to operate the equipment.
Product Wireless Information 13.56 MHz: Max -1.57 dBuA/m H-Field strength
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Wir besitzen keine Versand- und Lagerfläche in Deutschland und sind nicht von der Rücknahmepflicht nach § 17 ElektroG betroffen.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.