Support Document

0 mins to read


IOX-GARMINNT (Discontinued) IOX-GARMINWT (Discontinued) IOX-GARMINWTEU (Discontinued)

For the most up to date version, please visit: goo.gl/crx8u0

As an Authorized GARMIN Partner, Geotab® provides seamless integration with certain devices on the GARMIN platform. The GARMIN IOX™ allows users to connect a Geotab fleet management solution to a GARMIN device for enhanced in-vehicle driver-dispatcher communication.

Top Features

  1. Easy-to-install IOX™ to the Geotab GO™ device
    1. Two-way communication between drivers and dispatchers
    2. Dispatchers can send stops and routes directly to the vehicle
    3. Touchscreen communication for drivers
    4. Communications are verified and time-stamped
    5. All driver information is displayed on a map

IOX Garmin Drawing.png

IOX Hardware Technical Specifications

Weight

190 g

Size

Overall Length: 1900 mm L + FMI 15/45 cable

Widest Point: 43 mm W × 22 mm H

Housing

Black, moisture-resistant thermoplastic overmold

Interfaces

CAN: 500 kbps (for daisy chaining)

TTL serial interface

Power Output

GARMIN Interface: 900 mA @ 5 V

Daisy Chaining: 2500 mA @ 12 V/24 V

Current Rating

Operating Mode: 30 mA

Sleeping Mode: 0.2 mA

Temperature Rating

−40 ℃ to +85 ℃

Connectors

Male Mini-USB Type-B connector: Daisy chain power & CAN in

Female Mini-USB Type-B connector: Daisy chain power & CAN out

Male Mini-USB Type-B connector: GARMIN

Installation

Male Mini-USB connector connects to GO Device or another IOX

Male Mini-USB connector connects to GARMIN

Compatible Devices

All GO7® and newer devices and variants


IOX Installation Instructions

WARNING! Prior to IOX-GARMIN installation, read and follow GO device installation instructions (goo.gl/rkLRiA) to both verify that any existing GO device installation is correct and that you are qualified to complete this IOX-GARMIN installation. Incorrect installation of either the GO device, and/or IOX-GARMIN can result in loss of vehicle control and serious injury.

WARNING! Prior to IOX-GARMIN installation, please read and follow Important Safety Information and Limitations of Use, located at the end of the document. Always read and follow all safety information to prevent loss of vehicle control and serious injury.

How to Install IOX-GARMIN

1

Unplug the Geotab GO device from the vehicle and remove the IOX expansion port cover on the GO Device.

2

Plug the 90° USB connector from the IOX into the GO device. Secure the USB connector using a zip tie. Please note that over tightening the zip tie may damage the USB connector.

NOTE: Insert the USB connector in the orientation displayed in the image.

3

Once you connect the IOX-GARMIN to the GO device, plug in the GO device and immediately start the vehicle. The GO Device will enter debug mode.

4

Plug in the GARMIN.

NOTE: Please refer to the section below for GARMIN compatibility.

NOTE: The GO Device and GARMIN have similar USB connectors — it is possible to plug the USB into the wrong device. To help you remember, the IOX-GARMIN USB that plugs into the GO device has a notch at the end. Make sure you insert the correct connector into the corresponding device.

Garmin and Go Connector.png

5

Navigate to installmygps.com to verify that the device is communicating. In the space provided, enter your name, your company name, and the GO device serial number — found at the bottom of the device. Click Log Install.

6

After you click Log Install, the web page displays the current communication status of the device — in GREEN or RED text. If the device is communicating, the status is displayed in GREEN text. If the device is not communicating, the status is displayed in RED text.

NOTE: If the device is not communicating, please ensure the device is installed correctly and try again.

Termination Shunt

The IOX comes with a termination shunt installed in the expansion port. If you plan to install more than one IOX in a daisy chain you must remove the shunt from each device in the line, with the exception of the last IOX connected. The shunt must remain in the last IOX and secured with a zip tie.

The shunt in the last IOX device ensures the GO device detects and configures the IOX, as effectively as possible.

NOTE: Failure to install the shunt in the last IOX may affect IOX communication. To ensure the IOX communicates, please secure the shunt with a zip tie.

GARMIN Compatibility

For more information regarding traffic data for different GARMIN devices and the Fleet Management Interface (FMI) supported by each device, please refer to the GARMIN website.


Compatible GARMIN Devices

For a list of compatible GARMIN devices, please visit GARMIN’s Supported Devices page.

Geotab supports GARMIN models, listed in the table below, that use the FMI 15 or FMI 45 interface. The IOX-GARMIN is supplied with an FMI cable as per the table below. For additional information on supported features, visit GARMIN's page on the Geotab Marketplace.

IOX-GARMIN Device

FMI Cable

IOX-GARMINNT

No traffic, FMI 15 cable

IOX-GARMINWT

With traffic, FMI 45 cable (North America)

IOX-GARMINWTEU

With traffic, FMI 45 cable (Europe, Australia, NZ, and South Africa)

GARMIN HOS Solution (for GARMIN dēzl Devices)

If you have a Geotab GO device connected to a GARMIN dēzl device utilizing the GARMIN HOS solution, you must disable the Hours of Service (HOS) feature within MyGeotab™ using the steps below:

1

Navigate to my.geotab.com and log into the database where the GO device is registered

2

Select Vehicles, located in the navigation menu to the left.

3

Select the vehicle with the GARMIN DEZL installed.

4

Click More Details, located at the top of the page.

5

From the Device tab, scroll down to Hours of Service (HOS) and click Off.

6

Click Save.









Important Safety Information and Limitations of Use

For the latest version of Limitations of Use, please visit: goo.gl/k6Fp0w.

WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.

WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.

WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.

WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.

WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.

NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.

Regulatory Statements

Germany

Wir besitzen keine Versand- und Lagerfläche in Deutschland und sind nicht von der Rücknahmepflicht nach § 17 ElektroG betroffen.

scroll-up