Support Document

0 mins to read

July 4th, 2024

Installation Notes and Warnings

WARNING! Use Geotab telematics devices only with Geotab-approved harnesses acquired from Geotab-authorized channels. Use of non-Geotab harnesses from unauthorized channels can cause serious safety risks, including fire, and can lead to serious personal injury and/or damage to the vehicle.

! IMPORTANT: USA Only: Place the enclosed CARB Executive Order (EO) identification label sticker in the vehicle engine compartment, somewhere near the Vehicle Emission Control Information label on a smooth and clean surface. The EO identification label is required to aid inspection of the vehicle under the California Smog Check program and other applicable smog test programs. See here for more info...

! IMPORTANT: Customers with 12/24V vehicles who are planning to upgrade their device from GO8 or older models to GO9 or newer models are strongly recommended to replace the associated cable harness with an approved version. For a list of impacted harnesses and their approved versions, refer to the following document for more information.

NOTE: If a longer length is required to facilitate installation, connect a straight harness to a T-harness or another straight harness — where indicated below. The total harness length must not exceed 2 meters (or 6.5 feet).

NOTE: Regardless of the length, two T-harnesses CANNOT connect to each other. Connecting two T-harnesses, or any two harnesses that exceed 2 meters, compromises the integrity of the data and may cause issues with the vehicle’s Engine Control Unit (ECU).

! IMPORTANT: Some vehicles have multiple diagnostic connectors to choose from when installing a GO device. For further information to compare and contrast OBDII and RP1226, please visit the following link: https://gtb.page.link/hKF7.

Introduction

This document identifies all the harnesses available in MyAdmin, and the harnesses available by special order. This document also provides the following details for each harness:

  1. A description of the harness;
  2. The length of the harness;
  3. The purpose of the harness;
  4. The country of origin;
  5. The GO device supported by the harness (if applicable); and
  6. The renamed or replaced harness (if applicable).

For more information on how harnesses are named, please see Naming Conventions.


OBD Harnesses

HRN-BS16S4

Description

OBDII extension cable pack for GO devices. Replaces the HRN-INSTALLPACKV2.

Further Information

Replaces: HRN-INSTALLPACKV2

Length: 100 centimeters / 39 inches

Purpose: Used to extend the placement of the GO device. Recommended on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HS Code:

ECCN: EAR 99

HRN-BS16S4 23 June '14.jpg

HRN-BS16S4F

Description

Flat OBDII extension harness for GO devices. May lead to potential engine data limitations because Pin 1 (Single Wire CAN), and Pins 3 and 11 (Secondary CAN) are not populated.

Further Information

Length: 60 centimeters / 24 inches

Purpose: Used to connect the GO device to an OBD port that is covered by a panel — available in vehicles with low-profile connectors.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-BS16S5

Description

OBDII extension harness for GO devices.

Further Information

Length: 150 centimeters / 59 inches

Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-BS16S5 13 Jan '15.jpg

HRN-BD06A1

Description

Custom 6-pin adapter harness used to allow the GO device to access EV data from medium duty BYD EV buses. Applicable for buses made in Latin America (LatAm) only.

Further Information

Length: 10 centimeters / 4 inches

Purpose: Used to connect the GO device to BYD EV buses. Proprietary 6-pin to OBDII adapter. Applicable for BYD buses made in LatAm only.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China


HRN-BS16S5 13 Jan '15.jpg

HRN-BD06A12

Description

Custom proprietary harness for improved engine data support on select Peugeot, Citroen, Opel, and Vauxhall vehicles in Europe.

Further Information

Length: 5 centimeters / 2 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China


HRN-BS16S5 13 Jan '15.jpg

HRN-BU16Y5

Description

OBDII harness for GO devices. Includes special vehicle connector for receiving engine data from Mitsubishi Fuso and medium-duty vehicles.

Further Information

Documentation: Installation Instructions

Replaces: HRN-EZFUSO

Length: 130 centimeters / 51 inches

Purpose: Used specifically for Mitsubishi Fuso (medium duty) vehicles to allow capture of VIN and odometer. Requires connection to Fuso connector in addition to standard OBD port.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-BU16Y5 Rev.1 7 Apr '15.jpg

HRN-GS16K22

! IMPORTANT: Geotab prohibits the use of the 16-pin universal harness in North American Volvo/Mack 2019+ trucks when using a GO9 device, due to a known interoperability issue. Geotab has a specific harness intended for GO9 device installations, using HRN-CM24Y1 with HRN-CE10K2 or HRN-CS14S21 (14-pin connector).

document Image

Description

Universal OBDII T-Harness Kit for the GO device. Multi-adapter kit consisting of a T-harness (HRN-BM16T22) and 12 different mounting adapters for use in most light-duty, medium-duty, and heavy-duty vehicles, and is compatible with most models globally.

Further Information

Documentation: Support Document, Installation Instructions

Replaces: HRN-GS16K2

Length: 63 centimeters / 24.8 inches

Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly. The 12 different mounting adapters allow for installation in different vehicle makes and/or models. Region specific manufacturing, but no functionality differences.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China


Deutsch Connector Harnesses

HRN-DS09S4

Description

9-pin straight harness for North American heavy-duty Deutsch connector installations. Replaces HRN-C9HD.

Further Information

Replaces: HRN-C9HD

Length: 100 centimeters / 39 inches

Purpose: Straight harness used to move the GO device out of the way of the driver.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-DS09S4 Rev V2 8 Aug '16 JPEG.jpg

HRN-DS06S4

Description

6-pin straight harness for North American heavy-duty Deutsch connector installations. Replaces HRN-D6HD.

Further Information

Replaces: HRN-D6HD

Length: 100 centimeters / 39 inches

Purpose: Straight harness used to move the GO device out of the driver’s way. This harness has a standard 6-pin Deutsch connector and does NOT leave the Deutsch connector exposed.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-DS06S4 27 Oct '14.JPG

HRN-DS06T2

Description

6-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications. Replaces HRN-D6THD.

Further Information

Replaces: HRN-D6THD

Length: 60 centimeters / 24 inches

Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness has a standard 6-pin Deutsch connector.

What changed: The harness is now 60 centimeters in length (24 inches) allowing for GO device installation without an install pack.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-GS09K2

Description

Universal Heavy-Duty T-Harness Kit for the GO device.

Multi-adapter kit consisting of a 9-pin T-harness (HRN-DM09T2) and ​4 different mounting adapters (adapter 1 pre-installed) for use in most medium and heavy-duty international vehicles. Eliminates the need to know vehicle information in advance.

Further Information

Documentation: Support Document, Installation Instructions

Replaces: This harness replaces HRN-DR09T2 and HRN-DS09T2.

Length: 68 centimeters / 27 inches

Purpose: Used to extend the location of the GO device. Required on vehicles where the 9-pin diagnostic port is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the 9-pin diagnostic port location prevents the GO device from connecting properly. The 4 different mounting adapters allow for installation in different medium and heavy-duty vehicle makes and/or models.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image


Custom Harnesses

HRN-BF11A1

Description

Custom proprietary harness for improved engine data support on select Fiat/Chrysler vehicles in LatAm.

Further Information

Length: 20 centimeters / 8 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-BF11A1 Rev.1 31 March '17.jpg

HRN-BD16K1

Description

Battery disconnect bypass harness for GO device. For use on any vehicle with a positive battery terminal disconnect kill switch.This kit contains the harness and a fuse kit.

Further Information

! IMPORTANT: It is important to understand the risks involved when bypassing a master-power switch. The client must be informed and involved so that they understand and can approve the installation.

Length: 8 centimeters / 3.15 inches

Purpose: Used to maintain power to the GO device (maintain IOX learning, and heartbeats) when a vehicle is outfitted with a main battery disconnect kill switch.

Max length of connected cables: 2 meters / 6.5 feet (Exception: the red +V battery disconnect bypass wire may be extended by 3 meters / 10 feet with 16 AWG minimum).

Country of origin: China

document Image

HRN-CM24Y1

Description

Harness for custom GO device installations. Includes Molex connectors for two OBD connection points, and one J1939 connection point.

Further Information

Documentation: Installation Instructions: 2004-2018 Volvo Vehicles, 2006-2018 Mack Vehicles, 2016-2018 Hino Vehicles, 2019 Hino Vehicles, 2019+ Mack Vehicles, 2019+ Volvo Vehicles, 2019+ Mack (MR Series) Cab Over, 2017+ Isuzu Diesel Vehicles; Additional Installation Instructions: 2020 Mercedes Sprinter 2500 GO9 Installation

Replaces: HRN-INTCPDUAL

Length: 20 centimeters / 8 inches

Purpose: For custom installs that require multiple connection points to access engine data and engine protocols. The harness consists of an ALDL connector at one end for the GO device, a white 6-pin Molex connector for one OBD connection, a black 12-pin Molex connector for a second OBD connection, and a second 6-pin Molex connector for a J1939 connection (GO7 and GO8 only).

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CM24Y1 11 Aug '14.jpg

HRN-CW08K4

Description

Custom 8-wire harness kit for vehicles with no supported connectors. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit.

Further Information

Documentation: Support Document

PIN Definition: Red - Power Source, Black - Vehicle ground, Blue - J1939+/CAN High, White - J1939-/CAN Low, Brown - J1850-/J1708+, Green - J1850+/J1708-, Orange - ISO K-line, Grey - ISO L-line

Length: 80 centimeters / 31 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CW08A4, jpeg 6 Feb '17.jpgdocument Image

HRN-CH06A2

Description

Custom proprietary Hino adapter. Requires HRN-CM24Y1. Compatible with the 200-500 series for 2014-2018 vehicles.

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CH06A2 10 Feb '17 JPEG.jpg

HRN-CH10A2

Description

Custom 10-pin FMS adapter, compatible with all Hino vehicles 2019 or 2022. Requires HRN-CM24Y1. Also compatible with 100 series vehicles 2014 to 2018 .

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CE04A4

Description

Custom proprietary adapter for Volvo vehicles in Latin America and Europe. Requires HRN-CM24Y1.

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 80 centimeters / 31 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CE04A4, Rev.01 16 Mar '17.jpg

HRN-CE10K2

Description

Custom harness kit for Volvo/Mack heavy-duty vehicles, 2019 or newer, in North America. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit.

Further Information

Documentation: Installation Instructions: Mack 2019+ Vehicles, Volvo 2019+ Vehicles, Volvo 2004-2018 Vehicles, 2019+ Mack (MR Series) Cab Over.

Replaces: HRN-CE10A2 and SPR-VOVKIT

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Imagedocument Image

HRN-CG13S1

Description

Custom 13-pin adapter for use with HRN-GS16K2/HRN-GS16K22 Universal Harness kit.

Further Information

Documentation: Installation Instructions

Length: 10 centimeters / 4 inches

Purpose: An adapter to remove the power transient from a vehicle interface protocol.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CG04T3

Description

4-pin custom adapter for use with Volkswagen trucks only.

Further Information

Length: 60 centimeters / 24 inches

Purpose: OEM recommended connection point.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CI04A2

Description

Custom Isuzu FMS adapter (2017+). Requires HRN-CM24Y1 and Isuzu’s optional FMS kit.

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Purpose: This harness is only meant for diesel vehicles and supported engine data from the FMS port inside the vehicle.

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CK10K2

Description

Custom harness kit for Mack vehicles, 2018 or older, in North America. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit.

Further Information

Documentation: Installation Instructions

Replaces: HRN-CK10A2

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CK10A2 Rev.01 11 September, 2017.JPGdocument Image

HRN-CP04K2

Description

PSM module connection for Mercedes Sprinters (907 chassis) for Global markets. This kit contains the harness, HRN-CP04A2 and a fuse kit. Requires HRN-CM24Y1.

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 60 centimeters / 24 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CS14S21

Description

14-pin harness for heavy-duty applications. For use with any vehicle with an RP1226 diagnostic connection (refer to the Vehicle-Specific Installation Notes).

Further Information

Documentation: Installation Instructions

Length: 60 centimeters / 24 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CS14T2

Description

14-pin T-harness for heavy-duty applications. For use with vehicles with an RP1226 diagnostic connection.

Further Information

Documentation: Installation Instructions

Length: 60 centimeters / 24 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CT20T1

Description

Custom harness for Tesla Model 3 vehicles. Used in 2018 or older

Further Information

Requires: GO9 device

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CT20T11

Description

Custom harness for Tesla Model 3 vehicles, 2019 or newer.

Further Information

Requires: GO9 device

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CT06S1

Description

Custom harness for Tesla Model S and Model X vehicles, September 17, 2015 or newer.

Further Information

Requires: GO9 device

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CT06S2

Description

Custom harness for Tesla Model S, September 17, 2015 or older.

Further Information

Requires: GO9 device

Length: 30 centimeters /12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CT26T1

Description

Custom Tesla Model Y harness.

Further Information

Documentation: Installation Instructions

Requires: GO9 device

Length: 16.5 centimeters / 6.5 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-CX10S4

Description

Starter inhibit harness for Geotab Keyless. For use with an IOX-KEYLESS version B1 or newer for bladed key installations requiring starter inhibit functionality. NOT for use with non-labeled versions of IOX-KEYLESS.

Further Information

Replaces: HRN-CX09Y5 on B1 versions of IOX-KEYLESS

Requires: GO9 Device, works on HW version B1 or newer KEYLESS Hardware

Purpose: OPTIONAL used for IOX-KEYLESS installation to support Geotab KEYLESS Starter Inhibit applications

Length: 160 centimeters / 63 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-UP21Y2

Description

PSM module connection for Mercedes Sprinters for Global markets. Requires HRN-CM24Y1.

Further Information

Documentation: Installation Instructions

Replaces: HRN-SPRPSM

Length: 20 centimeters / 8 inches

Purpose: Used for PSM module connection on Mercedes Sprinters for Global markets in conjunction with HRN-CM24Y1.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-UP21Y2 15 Aug '14.jpg

HRN-CW03K3

! IMPORTANT: Customers with 12/24V vehicles who are planning to upgrade their device from GO8 or older models to GO9 or newer models are strongly recommended to replace the associated cable harness with an approved version. For a list of impacted harnesses and their approved versions, refer to the following document for more information.

Description

3-wire harness kit. The kit contains the harness and a fuse kit.

Further Information

Documentation: Support Document

Replaces: HRN-CW03S3

Length: 90 centimeters / 36 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-CW03S3 24 Jul '14.jpgdocument Image

HRN-CW03K4

Description

Custom 3-wire harness kit for GMCCC. The kit contains the harness and a fuse kit.

Further Information

Documentation: Support Document

Replaces: HRN-CW03S4

Length: 100 centimeters / 39 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

SPR-RELAYKIT

Description

Driver ID relay kit. Requires professional installation by a Geotab Authorized Installer or licensed automotive electrician or mechanic.

Further Information

Documentation: Installation Instructions

Replaces: HRN-RELAYKIT

Length: 60 centimeters / 24 inches

Purpose: Used as standalone on GO4V3 or in conjunction with the NFC driver ID on GO6, GO7, or GO8 devices. Driver ID keys drive a relay. Requires professional installation by a licensed automotive electrician/mechanic.

GO Devices supported: GO4v3, GO6, GO7, GO8

Country of origin: China

document Image

HRN-CL24T2

Description

Ford J1979 SGW Bypass Harness. Note: The State of California currently prohibits installing HRN-CL24T2 in a manner that relocates the in-vehicle diagnostic connector.

Further Information

Documentation: Installation Instructions

Length: 60 centimeters / 24 inches

Country of origin: China.

document Image

HRN-FUEL

Description

Fuel gauge tap-in adapter harness. Requires HRN-GS16K22.

Further Information

Documentation: AU Isuzu NPR 45/55-155 (RHD) Gen 6 2018, AU HINO 616 - 300 SERIES (RHD) Gen 8 2011

For a list of current supported vehicles, refer to the Fuel Harness Vehicle List.

Length: 64 centimeters / 25 inches

Country of origin: China.

document Image

HRN-FUEL3W

Description

Fuel gauge tap-in harness for 3-wire application.

Further Information

Documentation: AU Isuzu NPR 45/55-155 (RHD) Gen 6 2018, AU HINO 616 - 300 SERIES (RHD) Gen 8 2011

For a list of current supported vehicles, refer to the Fuel Harness Vehicle List.

Length: 75 centimeters / 29.5 inches

Country of origin: China.

document Image

GO RUGGED Harnesses

For further information on GO RUGGED Harnesses, please visit: https://gtb.page.link/TdJB

HRN-RC12T2

Description

A 12-pins Komatsu-specific harness for the GO RUGGED device, for 2010 or newer. Only functional for tier 4 engines (not tier 3).

Further Information

Documentation: Installation Instructions

Length: 42 centimeters / 17 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RD04S1

Description

Polaris interface harness for the GO RUGGED device.

Further Information

Length: 50 centimeters / 20 inches

Purpose: This harness is intended for Polaris off-road vehicles such as snowmobiles, all-terrain vehicles (ATV) and side-by-side vehicles. This is an ECM harness with the ability to capture engine data.

GO RUGGED Devices supported: GR7, GR8, GR9

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RMRCA1

Description

CAT specific adapter for the GO RUGGED device.

Further Information

Requires: HRN-GR09K1

Length: 10 centimeters / 4 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RS12S2

Description

12-way Amphenol weather resistant rugged harness for the GO RUGGED device —OBDII to 12 pin GO Rugged connector.

Further Information

Length: 30 centimeters / 12 inches

Purpose: Used to move the GO RUGGED device out of the driver’s way. Geared towards adverse weather conditions, does not leave the connector exposed.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RX06S4

Description

6-way IOX harness for the GO RUGGED device to provide IOX add-on support. The gray connector is weather resistant.

Further Information

Length: 100 centimeters / 39 inches

Purpose: Used for installation in vehicles or assets where auxiliary is needed.

Max length of connected cables: 1 meter / 3.2 feet

Country of origin: China

document Image

HRN-RW03K4

! IMPORTANT: Customers with 12/24V vehicles who are planning to upgrade their device from GO8 or older models to GO9 or newer models are strongly recommended to replace the associated cable harness with an approved version. For a list of impacted harnesses and their approved versions, refer to the following document for more information.

Description

3-wire harness kit for the GO RUGGED device. The kit contains the harness and a fuse kit.

Further Information

Documentation: Installation Instructions

Replaces: HRN-RW03S4

Length: 100 centimeters / 39 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RW08K1

Description

8-wire harness kit for the GO RUGGED device. The kit contains the harness and a fuse kit. Includes the HRN-RW08S1.

Further Information

Documentation: Installation Instructions

PIN Definition: Red - Power Source, Black - Vehicle ground, Blue - J1939+/CAN High, White - J1939-/CAN Low, Brown - J1850-/J1708+, Green - J1850+/J1708-, Orange - ISO K-line, Grey - ISO L-line

Length: 16.5 centimeters / 6.5 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Imagedocument Image

HRN-RW04K4

! IMPORTANT: Customers with 12/24V vehicles who are planning to upgrade their device from GO8 or older models to GO9 or newer models are strongly recommended to replace the associated cable harness with an approved version. For a list of impacted harnesses and their approved versions, refer to the following document for more information.

Description

Differential harness used for negative battery disconnect / oil pressure switch / negative output ignition for the GO RUGGED device. Required for ground service equipment. The kit contains the harness and a fuse kit. Includes HRN-RW04S4.

Further Information

Documentation: Installation Instructions

Length: 100 centimeters / 39 inches

Purpose: All equipment with ground disconnect on asset and or NON-ECM with no true ignition.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RZ04T4

Description

Kubota gasoline and diesel engines interface harness for the GO RUGGED device.

Further Information

Documentation: Installation Instructions

Length: 110 centimeters / 43 inches

Purpose: Kubota Type Engine MA-40-36 (Ground Service Equipment).

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RZ04S4

Description

Ford EDI TUG engine interface harness for the GO RUGGED device. Required for ground service equipment.

Further Information

Documentation: Installation Instructions

Length: 110 centimeters / 43 inches

Purpose: Ford engine type MSG-425. 2.5 liter

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RZ04T41

Description

Ford EDI TUG engine interface T-harness for the GO RUGGED device. Required for ground service equipment. Replaces HRN-RZ04S4

Further Information

Documentation:

Length: 110 centimeters / 43 inches

Purpose: Ford engine type MSG-425. 2.5 liter

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-RW03K5

Description

Pulse harness for engines not reporting ignition / RPM for the GO RUGGED device. Required for ground service equipment. The kit contains the harness and a fuse kit. Includes HRN-RW03S5.

Further Information

Documentation: Installation Instructions

Length: 122 centimeters / 48 inches

Purpose: NON-ECM with no true ignition using Low Voltage/Primary side of ignition coil.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RW07T1

Description

Tri-pin GO RUGGED device connector harness for vehicles without diagnostic ports (off-road vehicles only).

Further Information

Documentation: Installation Instructions, Installation Insert

Length: 20 centimeters / 8 inches

Purpose: Universal CAN connection used for off-road vehicles where available. Two wedge locks are supplied. The blue connection is most commonly used for the J1939, and the green connection can be used for certain applications with various types of heavy-duty equipment.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-RS12K1

Description

Battery disconnect bypass harness for the GO RUGGED device. For use on any vehicle with a positive battery terminal disconnect kill switch. The kit contains the harness and a fuse kit.

Further Information

! IMPORTANT: It is important to understand the risks involved when bypassing a master-power switch. The client must be informed and involved so that they understand and can approve the installation.

Length: 4 centimeters / 1.57 inches

Purpose: Used to maintain power to the GO device (maintain IOX learning, and heartbeats) when a vehicle is outfitted with a main battery disconnect kill switch.

Max length of connected cables: 2 meters / 6.5 feet (Exception: the red +V battery disconnect bypass wire may be extended by 3 meters/10 feet with 16 AWG minimum)

Country of origin: China

document Image

HRN-GR09K1

Description

Universal Rugged Heavy-Duty T-Harness Kit (IP67)

Further Information

Documentation: Support Document, Installation Instructions

Length: 25 centimeters / 9.8 inches

Purpose: Used to extend the location of the GO RUGGED device. This harness is built to IP67 standards for protection against dust and water. Required on vehicles where the 9-pin diagnostic port is located in an area where it is exposed to the elements. The 4 different mounting adapters allow for installation in different heavy-duty vehicle makes/models.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-DC14S2

Description

14-pin straight harness for CAT vehicles 2016+. IP67 rated when used along with the GO RUGGED device (harness revision 2 & 3 ONLY).

Further Information

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-DC14T1

Description

14-pin T-harness for CAT vehicles 2016+. IP67 rated when used along with the GO RUGGED device.

Further Information

Length: 27cm / 10.6 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-RL06T1

Description

6-pin harness for newer Bobcat equipment and assets (ie Bobcat Mini Excavators). The harness allows for engine data collection (J1939) if available.

Further Information

Length: 28 cm / 11 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China


document Image

HRN-RL07T1

Description

7-pin harness for all Bobcat Skid Steers 2000 & Up, 2008 Bobcat Excavators Up to 14 Tons. The harness allows for engine data collection (J1939) if available.

Further Information

Length: 26.5 cm / 10.4 inches

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China


document Image


European Heavy Goods Vehicle Harnesses

HRN-ES12S1

Description

OBDII harness for the GO device. Connects to the FMS connector primarily for European heavy-duty vehicles.

Further Information

Documentation: Installation Instructions

Replaces: HRN-FMSSTA

Length: 30 centimeters / 12 inches

Purpose: Straight harness used to connect directly to the dedicated telematics port common on European vehicles.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-ES12S1 13 Jan '15.jpg

HRN-EE14S1

Description

Mercedes diagnostic connector. Used on older generation medium duty trucks and buses.

Further Information

Replaces: HRN-EU14P

Length: 30 centimeters / 12 inches

Purpose: To move the GO device under the dashboard and out of sight. Like all harnesses, the HRN-EE14S1 provides power to the GO device and allows the GO device to record engine data for specific vehicles that require this type of connector.

Max length of connected cables: 1 meter / 3.3 feet

Country of origin: China

HRN-EE14S1 24 Jul '14.jpg

Special Order Harnesses

The following harnesses are only available by special order. Long lead times may exist. Contact your account Manager to determine prices, lead times, and to ensure it is the required harness.

HRN-BD16S5

Description

Harness for ALDL installations for gas and/or OBD vehicles (e.g. GM, Ford, etc.) and Freightliners with gateway.

Further Information

Length: 130.5 centimeters / 51.5 inches

Purpose: Uses OEM connector instead of using EZT bracket.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

document Image

HRN-UD03S6

Description

6 foot extension cable used for IOX-RS232D.

Further Information

Length: 180 centimeters / 6 feet

Purpose: To be used as extension cable with IOX-RS232D.

Country of origin: China

document Image

HRN-UD03S7

Description

8 foot extension cable used for IOX-RS232D.

Further Information

Length: 240 centimeters / 8 feet

Purpose: To be used as extension cable with IOX-RS232D.

Country of origin: China

document Image

HRN-UD03S8

Description

10 foot extension cable used for IOX-RS232D.

Further Information

Length: 300 centimeters / 10 feet

Purpose: To be used as extension cable with IOX-RS232D.

Country of origin: China

document Image

HRN-UD03S9

Description

14 foot extension cable used for IOX-RS232D.

Further Information

Length: 420 centimeters / 14 feet

Purpose: To be used as extension cable with IOX-RS232D.

Country of origin: China

document Image

Installation Accessories

The following items are commonly ordered with harnesses to properly secure GO devices in vehicles.

SPR-INSTALLBAG

Description

Mounting bracket and material for the GO device. For installation purposes, the package includes 2 zip seals, 2 screws, and double-sided tape for the bracket.

Further Information

Purpose: Provides installers with mounting material to ease GO device installation.

Installing the mounting bracket: Use the screws or double-sided tape to affix the bracket to the vehicle. Place the GO device in the bracket as shown in the image.

Country of origin: China

SPR-INSTALLBAG 15 Aug '14.jpg

document Image

SPR-NFCBRACKET

Description

Mounting bracket and holder for IOX-NFCREADER. For installation purposes, the package includes 2 screws and double-sided tape for the bracket.

Further Information

Purpose: Provides installers with a replacement mounting bracket for the NFC Reader.

Installing the mounting bracket: Use the screws or double-sided tape to affix the bracket to the vehicle.

Country of origin: China

SPR-NFCBRACKET.JPG

SPR-BSFBKT

Description

Bracket required for 2015 Ford F-150, Ford Fusion, and Ford Mondeo vehicles.

Further Information

Purpose: To support the connection between a GO device and the HRN-BS16T2 in certain Ford vehicles.

Country of origin:

SPR-BSFBKT 10 July '15.jpg

HRN-IOXEXT

Description

Extension harness for IOX hardware. Cable length is 2 meters (79 inches).

Further Information

Purpose: Extension cable that connects IOX hardware on one end, and the GO device on the other to prevent interference and minimize obstruction. Can also be used to connect two IOX devices.

Country of origin: China

document Image

HRN-IOXEXT-A

Description

Extension harness for IOX hardware. Cable length is 2 meters (79 inches). TAA Compliant.

Further Information

Purpose: Extension cable that connects IOX hardware on one end, and the GO device on the other to prevent interference and minimize obstruction. Can also be used to connect two IOX devices.

Country of origin: Taiwan

document Image

Discontinued Harnesses

OBD Harnesses

HRN-BS16T2 (Discontinued)

Description

OBDII T-harness for the GO device. Replaced HRN-EZT.

Further Information

Replaces: HRN-EZT

Length: 50 centimeters / 20 inches

Purpose: To move the GO device under the dashboard and out of sight while leaving the OBD connector exposed.

Max length of connected cables: 2 meters / 6.5 feet

HRN-BS16T2 13 Jan '15 (2).jpg

HRN-BT16T2 (Discontinued)

Description

OBDII Extension T-harness for the GO device. Required globally for Ford Transit Connect and Ford Transit Full Size Vans. May be required in other Ford, Land Rover, and Jaguar vehicles; and Asian vehicles such as Honda, Mitsubishi, Nissan, Toyota, Kia, and Hyundai.

Further Information

Length: 50 centimeters / 20 inches

Purpose: With vehicle-specific OBD connectors, this T-harness connects to vehicles found in Global markets. It allows the OBD connector to remain exposed and with the GO device installed under the dashboard and out of sight. It is required for many European vehicles, some of which are in North America. These include the Ford Focus, B-Max, C-Max, S-Max, Fiesta, Mondeo (Model Year 2014 and earlier), Galaxy, Kuga, EcoSport, Transit Connect, and 2016 Ford Escape.

Max length of connected cables: 2 meters / 6.5 feet

HRN-BT16T2, 23 Oct '15 JPEG.jpg

HRN-BE16T2 (Discontinued)

Description

OBDII T-harness for the GO device. Mercedes-specific connector. Commonly used for Sprinters for NA and Europe — that DO NOT connect to a Parametric Special Module (PSM) — and Volvo and Mack NA Trucks (2014 and 2015 model years).

Further Information

Length: 50 centimeters / 20 inches

Purpose: With a Mercedes specific OBD connector, this T-harness connects to Mercedes Sprinters commonly found in Global markets. It is NOT used to connect to a PSM in the vehicle. It is also used to connect to North American Volvos and Mack Trucks (2014 and 2015 model years). Allows the OBD connector to remain exposed with the GO device installed under the dashboard and out of sight.

Max length of connected cables: 2 meters / 6.5 feet

pa-image-jan20-3.jpg

HRN-BF16T2 (Discontinued)

Description

OBDII Extension T-harness for the GO device. Primarily for European markets. Special connectors for Mercedes Benz and also Citroen, Peugeot, Renault, Dacia, FIAT, Alfa Romeo, and certain Iveco vehicles.

Further Information

Length: 50 centimeters / 20 inches

Purpose: With vehicle-specific OBD connectors, this T-harness connects to European-manufactured vehicles found in Global markets. It is NOT used to connect to a PSM in the vehicle. Allows the OBD connector to remain exposed with the GO device installed under the dashboard and out of sight.

Max length of connected cables: 2 meters / 6.5 feet

HRN-BF16T2 24 Jul '15.jpg

HRN-GS16K2 (Discontinued)

! IMPORTANT: Geotab prohibits the use of the 16-pin universal harness in North American Volvo/Mack 2019+ trucks when using a version 9 GO device, due to a known interoperability issue. Geotab has a specific harness intended for version 9 GO device installations (HRN-CM24Y1 with HRN-CE10A2 or HRN-CS14S21 14-pin connector).

! IMPORTANT: The State of California currently prohibits Installing HRN-GS16K2 in a manner that relocates the in-vehicle diagnostic connector. See HRN-GS16K2 Installation - Direct Plug-In for guidance on installing this harness using a direct plugin installation method without relocating the data link connector. Alternatively, GO devices can be installed directly into the OBDII port using an extension/conversion harness that plugs directly into the OBDII port or other emissions diagnostic data link connector port.

document Image

Description

Universal OBDII T-Harness Kit for the GO device. Multi-adapter kit consisting of a T-harness (HRN-BM16T2) and 12 different mounting adapters for use in most light-duty, medium-duty, and heavy-duty vehicles, and is compatible with most models globally. HRN-GS16K2 is replaced by HRN-GS16K22

Further Information

Documentation: Support Document, Installation Instructions; Additional installation instructions: Mitsubishi Fuso 2010-2021 GO9 Installation

Replaces: HRN-BE16T2, HRN-BG16T2, HRN-BF16T2, HRN-BS16T2, HRN-BT16T2

Length: 60 centimeters / 24 inches

Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly. The 12 different mounting adapters allow for installation in different vehicle makes and/or models. Region specific manufacturing, but no functionality differences.

Max length of connected cables: 2 meters / 6.5 feet

HRN-BG16T2 24 Jul '15.jpg

Deutsch Connector Harnesses

HRN-DR09T2 (Discontinued)

Description

9-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications and is a THREADED dash mount style. Replaces HRN-CD9TBHD.

Further Information

Replaces: HRN-CD9TBHD

Length: 60 centimeters / 24 inches

Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness is different from a standard 9-pin Deutsch connector harness because it uses a threaded connector. The threaded connector is becoming more common within the heavy-duty market. The following vehicles require the HRN-DR09T2 harness:

  1. 2008 and newer Peterbilt trucks;
  2. 2013 and newer Kenworth trucks; and
  3. 2013 and newer Freightliner (Large).
  4. The following vehicles do not require the HRN-DR09T2 harness:

  5. Mack;
  6. Internationals; and
  7. Lighter Freightliners.
  8. Max length of connected cables: 2 meters / 6.5 feet

document Image

HRN-DS09T2 (Discontinued)

Description

9-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications.

Further Information

Replaces: HRN-CD9THD

Length: 60 centimeters / 24 inches

Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness has a standard 9-pin Deutsch connector.

Max length of connected cables: 2 meters / 6.5 feet

document Image

HRN-DC09T2 (Discontinued)

Description

Special harness for CAT off-road vehicles. Replaces HRN-TCATHD.

NOTE: Verify that the vehicle does not use a standard 9-pin connector.

Further Information

Replaces: HRN-TCATHD

Length: 30 centimeters / 12 inches

Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed.

Max length of connected cables: 1 meter / 3.3 feet

HRN-DC09T2 30 Jan '15.jpg

Custom Harnesses

HRN-BS04A1 (Discontinued)

Description

Adapter harness for use with HRN-DS09T2, HRN-DT09T2 and HRN-GS09K2, for improved engine support for 2017 Kenworth and Peterbilt trucks.

Further Information

Requires: HRN-GS09K2

Replacements:The HRN-BS04A1adapter harness is only required if using the GO7 or GO8 devices. It was not required for the GO9. There is no replacement harness. The solution is to replace the device with a GO9, which is designed to directly support enhanced engine data.

Length: 6.3 centimeters / 2.5 inches

Purpose: Used specifically for 2017+ Kenworth and Peterbilt trucks with Paccar engines MX13/MX15 to obtain improved engine data.

Max length of connected cables: 2 meters / 6.5 feet

Country of origin: China

HRN-BS04A1 20 Jan 2017 JPEG.jpg



HRN-CW08A4 (Discontinued)

Description

8-wire pigtail adapter for vehicles with connectors that are not supported on any other harness. Requires HRN-CM24Y1.

Further Information

Requires: HRN-CM24Y1

PIN Definition: Red - Power Source, Black - Vehicle ground, Blue - J1939+/CAN High, White - J1939-/CAN Low, Brown - J1850-/J1708+, Green - J1850+/J1708-, Orange - ISO K-line, Grey - ISO L-line

Length: 80 centimeters / 31 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-CW08A4, jpeg 6 Feb '17.jpg

HRN-CE10A2 (Discontinued)

Description

Custom adapter for Volvo vehicles in North America. Requires HRN-CM24Y1.

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-CE10A2 Rev.02 17 May '17.jpg

HRN-CK10A2 (Discontinued)

Description

Custom adapter for Mack vehicles in North America. Requires HRN-CM24Y1.

Further Information

Requires: HRN-CM24Y1

Length: 30 centimeters / 12 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-CK10A2 Rev.01 11 September, 2017.JPG

HRN-CT06A1 (Discontinued)

Description

Custom adapter for Tesla Model S vehicles. Requires HRN-CM24Y1.

Further Information

Requires: HRN-CM24Y1

Length: 10 centimeters / 4 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-CT06A1 - August 22, 2017.jpg

HRN-CT06A11 (Discontinued)

Description

Custom adapter for Tesla Model S and Model X vehicles. Requires HRN-CM24Y1.

Further Information

Requires: HRN-CM24Y1

Length: 20 centimeters / 8 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-CT06A1 - August 22, 2017.jpg

HRN-CW03S3 (Discontinued)

Description

Custom 3-wire harness for the GO device — PWR, GND, IGN. Replaces HRN-2WCP for GO6, which cannot take advantage of the IGN wire. Replaced by kit HRN-CW03K3. The kit contains the harness and a fuse kit

Further Information

Documentation: Support Document (goo.gl/VEvruL)

Replaces: HRN-3WCP

Length: 90 centimeters / 36 inches

Purpose: Used for installation in vehicles or assets where no engine data is available.

Max length of connected cables: 2 meters / 6.5 feet

HRN-CW03S3 24 Jul '14.jpg


HRN-CP04A2 (Discontinued)

Description

PSM module connection for Mercedes Sprinters (907 chassis) for Global markets. Requires HRN-CM24Y1. Replaced by kit HRN-CP04K2. The kit contains the harness and a fuse kit

Further Information

Documentation: Installation Instructions

Requires: HRN-CM24Y1

Length: 60 centimeters / 24 inches

Max length of connected cables: 2 meters / 6.5 feet

document Image

GO RUGGED Harnesses

HRN-RW03S4 (Discontinued)

Description

3-wire harness for the GO RUGGED device — PWR, GND, IGN. Replaced by kit HRN-RW03K4. The kit contains the harness and a fuse kit.

Further Information

Length: 100 centimeters / 39 inches

Max length of connected cables: 2 meters / 6.5 feet

HRN-RW03S4, jpeg 17 Apr '17.tif.jpg

HRN-RW04S4 (Discontinued)

Description

Differential harness used for negative battery disconnect / oil pressure switch / negative output ignition for the GO RUGGED device. Required for ground service equipment. Replaced by kit HRN-RW04K4. The kit contains the harness and a fuse kit

Further Information

Documentation: Installation Instructions

Length: 100 centimeters / 39 inches

Purpose: All equipment with ground disconnect on asset and or NON-ECM with no true ignition.

Max length of connected cables: 2 meters / 6.5 feet

document Image

HRN-RW03S5 (Discontinued)

Description

Pulse harness for engines not reporting ignition / RPM for the GO RUGGED device. Required for ground service equipment. Replaced by kit HRN-RW03K5. The kit contains the harness and a fuse kit

Further Information

Documentation: Installation Instructions

Length: 122 centimeters / 48 inches

Purpose: NON-ECM with no true ignition using Low Voltage/Primary side of ignition coil.

Max length of connected cables: 2 meters / 6.5 feet

document Image

Special Order Harnesses

HRN-BD16S4 (Discontinued)

Description

Custom order third-party device harness. No longer used for Valor implementations.

Further Information

Length: 100 centimeters / 40 inches

Purpose: Harness used in custom situations. Please discuss with Geotab Support or your Account Manager to determine if harness is appropriate.

Max length of connected cables: 1 meter / 3.3 feet

HRN-E1 Fuseless, 7 Feb '14.JPG

HRN-CMDMY3 (Discontinued)

Description

Harness for gas Freightliner without gateway. Requires HRN-BD16S4 (E1).

Further Information

Length: 80 centimeters / 31.5 inches

Purpose: Designed for OEM Freightliner walk-in van chassis with Gas engines, 2009 and newer model years installed with GO4 units. Also requires an HRN-BD16S4.

Includes an ALDL connector on one end to connect the HRN-E1 harness, a 6-pin Molex connector for OBD connections.

Max length of connected cables: 2 meters / 6.5 feet

HRN-CMDMY3 24 Jul '14.jpg

European Heavy Goods Vehicle Harnesses

HRN-EA16S1 (Discontinued)

Description

Diagnostic connector designed for European markets, primarily for the DAF Euro 3 (up to 2006). Replaces HRN-EU16P.

Further Information

Length: 30 centimeters / 12 inches

Purpose: To move the GO device under the dashboard and out of sight. Like all harnesses, the HRN-EA16S1 provides power and engine data for specific vehicles that require this type of connector.

Max length of connected cables: 1 meter / 3.3 feet

Country of origin: China

HRN-EA16S1 Rev.4 10 July '15.jpg

Naming Conventions

This section outlines the harness naming convention and provides definitions for each character or group of characters.

Harnesses all start with an HRN prefix followed by 6-character names, as defined below. All characters are alphanumeric and, to avoid confusion, no I’s or O’s are used.

Examples:

    1. HRN-DS09T2
      1. D represents a Deutsch connector.
      2. S represents a Standard OBD, Deutsch, or FMS connector.
      3. 09 represents 9 pins / wires.
      4. T represents a T-harness.
      5. 2 represents a length in the range of 12-24 inches or 30-60 cm.
    2. HRN-BS16S4
      1. B represents OBD type connectors.
      2. S represents a Standard OBD, Deutsch, or FMS connector.
      3. 16 represents 16 pins / wires.
      4. S represents a straight harness.
      5. 4 represents a length in the range of 36-48 inches or 120-152 cm.
    3. HRN-CW03S3
      1. C represents a Custom harness.
      2. W represents a Harness with exposed wires.
      3. 03 represents 3 pins / wires.
      4. S represents a Straight harness.
      5. 3 represents a length in the range of 24-36 inches or 60-90 cm.

    Harness Naming — Table of Definitions

    Category

    Family

    Connections

    Type

    Length

    Sub-Type

    Defined broad category of harnesses (Deutsch, OBDII, European, custom, etc.)

    Defines family of harnesses which can be common, manufacturer specific, proprietary, etc.

    Number of pins used or specific connections connecting up to an asset

    Harness Type (i.e. straight, split, etc.)

    Length of harness between the vehicle connector and GO device

    Harness Sub-Type for different variants of the same harness

    Code + Definition

    Code + Definition

    Code + Definition

    Code + Definition

    Code + Definition

    Code + Definition

    A – Auxiliary connector

    A – DAF-specific connector

    01 – 1 pins/wires

    A – Adapter harnesses

    1 – 0-30 cm (0-12 inches)

    F – Flat cable

    B – ODB-type connectors

    C – Komatsu-specific, and Caterpillar-specific connectors

    02 – 2 pins/wires

    B – Bare wire

    2 – 30-60 cm (12-24 inches)

    U – Customer Specific

    C – Custom harness

    D – Delphi-specific connector

    03 – 3 pins/wires

    K – Kit contains more than one part

    3 – 60-90 cm (24-36 inches)

    1-9 – Numeric code for harness updates

    D – Deutsch connectors

    E – Mercedes connector and Volvo/Mack Truck specific connectors

    04 – 4 pins/wires

    S – Straight harnesses

    4 – 90-120 cm (36-48 inches)

    A Region specific manufacturing, but no functionality differences

    E – European Imported Heavy Goods vehicle style connectors

    F – Mercedes & Citroen, Peugeot, Renault, Fiat specific connectors

    06 – 6 pins/wires

    T – T-harnesses

    5 – 120-158 cm (48-60 inches)

    G – Global

    G – BMW & Volkswagen, Audi, Seat, Skoda specific connectors

    08 – 08 pins/wires

    Y – Connects up to two or more different connectors

    6 – 158 -243 cm (60 -96 inches)

    R Rugged

    H – Hino-specific connector

    09 – 09 pins/wires

    7 – 244-303 cm (96-119 inches)

    U – Dual protocol, extension harness

    I – Isuzu-specific connector

    10 – 10 pins/wires

    8 – 304-426 cm (120-167 inches)

    K – Mack Truck specific connectors

    11 – 11 pins/wires

    9 – 427-1000 cm (168-394 inches)

    L – Specific applications

    12 – 12 pins/wires

    10 – 1000+cm (394+ inches)

    M – Multiple connectors

    14 – 14 pins/wires

    N – Navistar

    16 – 16 pins/wires

    P – Sprinter PSM connectors

    20 – 20 pins/wires

    R – Threaded type 9-pin Deutsch connector

    21 – 21 pins/wires

    S – Standard OBD, Deutsch, or FMS connector

    24 – 24 pins/wires

    T – Tesla-specific connector

    DM – Delphi Molex Connectors

    U – Fuso-specific connector

    RC – Rugged CAT Connectors

    V – Iveco-specific connector

    W – Harness with exposed wires

    X – IOX

    Z – TUG-specific connector

  • scroll-up